If you want to add value and beauty to the exterior of your home, one of the easiest, least expensive ways is by adding a patio door. Installing a new patio door is something any do-it-yourselfer with common sense can accomplish in just a few hours. If you have an existing door, you may want to consider sliding door repair as a cheaper option. For installing a patio door, follow this helpful guide to get your project started.
1. Prep Work
The first thing you need to do is contact your local building inspector and ask about the necessary permits for replacing a patio door in your area. If you are installing a pre-hung unit, you should already comply with all applicable city codes, but still, check to be sure. You will also need to check your local building codes regarding window installation to ensure you are putting in enough insulation around the new door.
2. Remove Old Door
If replacing an existing patio door, you can skip this step and proceed to #3 (if not, keep reading). The first thing you want to do is remove the old door. If it has a screen, cut the screen away from the frame and remove all of the screws that hold it in place. Then remove all weatherstripping between the door and storm door, along with any caulking within the existing frame. A professional expert from a sliding glass door repair company like here will inspect the door and determine if it is suitable for sliding door repair.
3. The New Door
© GreenhouseCenter, since 2020. Unauthorized use and/or duplication of this material without express and written permission from this site’s author and/or owner is strictly prohibited. Excerpts and links may be used, provided that full and clear credit is given to Jon Rowland and GreenhouseCenter.net with appropriate and specific direction to the original content.
When you have selected your new patio door, the first step is to remove any caulk from the existing frame of your home. Next, make sure you have all of your tools and materials together. After that, read the directions on your patio door carefully before starting and executing accordingly.
Read more: San Diego Glass Doors – Custom Interior Sliding Doors For Your Place
4. Assemble the New Door
This is where you want to ensure you have all your tools and materials together. Assembling a pre-hung door will come packaged with everything you need (including screws and nails). Pre-hung units snap tightly into place and should only require a rubber mallet for final placement.
Recheck all of your measurements and make any necessary adjustments before installing the door. This step usually only takes a few minutes, but if this is your first attempt at establishing a patio door, you may want to allow a touch more time.
5. Nailing It In Place
Now that everything is in place begin nailing the door to the frame. You want to make sure that everything is lined up before you start hammering in the nails – if this is your first time installing a patio door, do not be discouraged by any minor setbacks at this point. Even experienced installers have occasional misalignments and will need to recheck their measurements.
6. Window Stops
Finally, once you are satisfied that your new patio door is installed correctly, it is time to attach the window stops to keep everything in place properly. Make sure you have measured them carefully before installation – if they are too long, they will be challenging to work with, and if they are too short, you will have problems closing your door.
7. Trim It Out
Now that your new patio door is installed. The finishing touch will be installing all the necessary trim pieces left. Just follow the directions included with the new door – there should be no problem putting them in, especially if you have a pre-hung unit.
8. 2″ Foam Insulation
Finally, this is the last step – closing up any cracks in your home with a spool of 2″ foam insulation. If you live in a cold climate, you must put in enough insulation around your new patio door, as it is a significant source of heat loss.
9. Weatherstrip It
You should place weatherstripping between the door and the storm door to seal the gap. You can buy this accessory at any local hardware store or use extra caulking from your original installation kit.
Read more: Why Should You Consider Aleko Automatic Doors?
10. Install the Screen
Now that you have finished installing your new patio door, it’s time to install the screen. You can use any screen kit (available anywhere) to take out the old screen and install the new one. Remember to ensure that you attach it to the door frame tightly so your family doesn’t get any uninvited bugs or critters through.
There you have it! You can always install a new patio door where sliding door repair does not work.